Installation Guide
Spring Kitchen Faucet Installation Guide
Tools & Materials Needed
Tools Required:
- Adjustable wrench or basin wrench
- Phillips and flathead screwdrivers
- Plumber's tape (Teflon tape)
- Flashlight
- Bucket or towel (for water drainage)
- Pliers (optional)
- Silicone sealant (optional)
What's Included in Your Kit:
- Spring faucet body with pull-down spray head
- Mounting hardware (washers, nuts, screws)
- Two flexible supply lines (hot and cold)
- Rubber gaskets and O-rings
- Spring coil assembly
- Installation manual
Before You Begin
Estimated Installation Time: 30-45 minutes
Important Safety Notes:
- Turn off the water supply valves under the sink (both hot and cold)
- Turn on the old faucet to release any remaining water pressure
- Place a bucket under the connections to catch any residual water
- Have adequate lighting to see under the sink clearly
Step-by-Step Installation Instructions
Step 1: Remove Old Faucet
- Disconnect supply lines: Use an adjustable wrench to disconnect the hot and cold water supply lines from the old faucet
- Remove mounting nuts: Use a basin wrench to loosen and remove the mounting nuts holding the faucet to the sink
- Lift out old faucet: Once all connections are removed, lift the old faucet straight up and out
- Clean the surface: Thoroughly clean the sink surface where the new faucet will mount, removing any old putty or debris
Pro Tip: Take photos of your old faucet connections before removing them for reference.
Step 2: Prepare the New Faucet
- Check all parts: Lay out all components and verify everything is included
- Install rubber gasket: Place the large rubber gasket on the bottom of the faucet base (if not pre-installed)
- Thread supply lines: Feed the supply lines and spring hose through the gasket
- Apply plumber's tape: Wrap 3-4 layers of plumber's tape clockwise around the threads of both supply line connections
Important: Make sure the rubber gasket sits flat against the faucet base for a proper seal.
Step 3: Position Faucet on Sink
- Feed lines through hole: Carefully feed the supply lines and pull-down hose through the mounting hole in your sink or countertop
- Position the faucet: Center the faucet on the mounting hole, ensuring it faces the correct direction
- Press firmly: Push down gently to seat the rubber gasket against the sink surface
- Check alignment: From above, verify the faucet is properly aligned before moving to the next step
Note: For sinks without pre-drilled holes, ensure your hole is 1.25" - 1.5" in diameter.
Step 4: Secure Mounting Hardware (Under Sink)
- Slide on mounting bracket: From underneath, slide the metal or plastic mounting bracket over the supply lines
- Add washers and nuts: Place the rubber washer, then metal washer, then thread on the mounting nut
- Hand-tighten first: Thread the mounting nuts by hand to avoid cross-threading
- Tighten with wrench: Use a basin wrench or adjustable wrench to firmly tighten the nuts (do not over-tighten)
- Check faucet stability: Try gently moving the faucet from above - it should be completely stable
Pro Tip: Alternate tightening between nuts if there are multiple mounting points to ensure even pressure.
Step 5: Install Spring Coil Weight
- Locate the weight: Find the cylindrical weight that came with your faucet
- Thread onto hose: Slide the weight onto the pull-down hose above the connection point
- Position correctly: The weight should hang freely and help the hose retract smoothly
- Test movement: Pull down the spray head and release - the weight should help it snap back
Important: The weight is essential for proper hose retraction. Do not skip this step.
Step 6: Connect Water Supply Lines
- Identify hot and cold: Hot water connects to the left supply line, cold to the right (when facing the faucet)
- Connect to shut-off valves: Thread each supply line onto the corresponding shut-off valve under the sink
- Hand-tighten first: Start by hand to ensure proper threading
- Wrench-tighten: Use an adjustable wrench to tighten an additional 1/4 to 1/2 turn
- Don't over-tighten: Over-tightening can damage the connections and cause leaks
Reminder: Red markings typically indicate hot water connections.
Step 7: Install Pull-Down Spray Head
- Connect spray head: The spray head should already be connected, but verify the connection is secure
- Thread through collar: Make sure the hose passes through the spring collar properly
- Check spray modes: Most spray heads have 2-3 spray patterns - verify the button or switch works
- Ensure smooth operation: Pull the spray head down and release several times to check for smooth movement
Step 8: Turn On Water Supply & Test
- Open shut-off valves: Slowly turn both hot and cold water shut-off valves to the open position
- Check for leaks: Immediately inspect all connections under the sink for any water leaks
- Turn on faucet: Open the faucet to release air from the lines (water may sputter initially)
- Test both temperatures: Run hot and cold water to verify both work properly
- Test spray head: Pull down the spray head and test all spray functions
- Check for drips: Let water run for 2-3 minutes, then turn off and check for any dripping
If you notice leaks: Turn off water, dry the area, and tighten the leaking connection slightly.
Step 9: Final Adjustments & Cleanup
- Adjust spray head tension: Some models have adjustable tension for the pull-down mechanism
- Clean the faucet: Wipe down the faucet with a soft cloth to remove fingerprints
- Test full rotation: Ensure the faucet rotates smoothly 360° (if applicable)
- Verify stability: Check that the faucet doesn't move when operating the handle
- Remove any labels: Peel off any protective stickers or labels
Troubleshooting Common Issues
Problem: Low water pressure
Solution:
- Remove and clean the aerator (unscrew from spout tip)
- Check that supply valves are fully open
- Verify supply lines aren't kinked
Problem: Spray head won't retract
Solution:
- Check that the weight is properly installed
- Ensure the hose isn't tangled or caught under the sink
- Verify the spring mechanism isn't obstructed
Problem: Water leaking from base
Solution:
- Tighten mounting nuts slightly
- Check that rubber gasket is properly seated
- Verify O-rings are in place on supply connections
Problem: Handle is loose or wobbly
Solution:
- Tighten the set screw on the handle (usually hidden under a cap)
- Check that mounting hardware is secure
Problem: Spray modes not switching
Solution:
- Clean spray head button/switch
- Check for mineral buildup around spray face
- Verify hose connection is secure
Maintenance Tips
Daily Care:
- Wipe down with a soft cloth after each use
- Avoid abrasive cleaners or scrubbing pads
- Dry water spots to prevent mineral buildup
Monthly Maintenance:
- Clean aerator to maintain water pressure
- Inspect spray head for mineral deposits
- Check under sink for any moisture or leaks
Annual Maintenance:
- Inspect all connections for wear
- Replace O-rings if needed
- Lubricate moving parts if necessary
Warranty & Support
Your spring kitchen faucet includes a manufacturer's warranty covering defects in materials and workmanship. Keep your receipt and product information for warranty claims.
For Additional Help:
- Visit our website for video installation tutorials
- Contact customer support: support@yourstore.com
- Live chat available Mon-Fri, 9 AM - 6 PM
Safety Reminders
⚠️ Always turn off water supply before installation ⚠️ Do not use excessive force when tightening connections ⚠️ Test for leaks immediately after turning water back on ⚠️ If you're uncomfortable with any step, consult a licensed plumber ⚠️ Follow local plumbing codes and regulations
Congratulations! Your new spring kitchen faucet is now installed and ready to use. Enjoy the enhanced functionality and style it brings to your kitchen!
Need the complete installation as a PDF? Contact us and we'll send you a printable version with detailed diagrams.
